1、机构 Mechanical

1-1、外观尺寸 External dimension

92mm*92mm*38mm

1-2、重量 Weight

367.16g

1-3、轴承 Bearing

滚珠 TWO BALL BEARING

2、 电气特性 Electrical characteristics(在通风及额定电压条件下 in free air at rated voltage)

2-1、额定电压 Rated voltage

110V/50Hz

2-2、额定电流 Rated current

0.13±0.01A

2-3、额定输入功率 Rated input power

14±10%W

3、 效率 Efficiency

3-1、风扇转数速 Rated speed(范围 range)

2300±10%RPM

3-2、最大风量 Maximum air flow

28CFM

3-3、最大静压 Maximum static air pressure

3.5mmH2O

4、 特性规格 Characteristics

4-1、 操作电压 Operating voltage range

80V-125V

4-2、 起动电压 Staring voltage

80V

4-3、 锁定电流 Locked current

4-4、 操作温度 Operating temperature

-10℃~+70℃

4-5、 储存温度 Storage temperature

-20+85℃

4-6、 框外类型  Outside the box type:

□端子型 Terminal type

□导线型 Axial lead            线长 Lead long (A)= □150

□220□230□240□250  □270□380□480□570□800

□1000( ■表示选择项 Said options）

4-7、 环境湿度测试 Environment humidity

10%(RH)45 ℃ for 24 hours & 98% (RH) 45 ℃ for 24

hours

4-8、 绝缘阻抗强度 Insulation resistance

在本体与两条导线间加 500V 直流电压之绝缘阻抗

10MΩ以上            At least 10MΩ at 500 VDC between housing and both lead wires

4-9、 绝缘耐压强度 Dielectric strength

必须能抵抗在本体与两线间加 2000V 交流电压 1 分钟

1mA                                       Withstand 2000 VAC 1 minute 1mA between housing and both lead wires

4-10、预期寿命(MTBF)：指在额定电压及正常温度，湿度条件下连续运转。

Life expectancy:continuous operation at rated voltage and normal temperature & humidity

4-10-1、含油轴承寿命：30000 小时

Sleeve bearing life expectance:30000Hours

4-10-2、双滚珠轴承预期寿命：50000 小时

Two balls bearing life expectance:50000Hours

4-11、端子抗拉强度 Tensible strength of connector

端子以 1 公斤的拉力拉扯 15 秒不会脱落

Connector will not be any broken at 1 Kg for 15 seconds per piece.

4-11、★噪音分贝 Acoustic sound vel

20.0dBA

4-11-1、噪音测试说明 Acoustic sound level test descriptions

以额定电压在噪音实验室中测试背景噪音 14.9 分贝      悬吊 Suspension

At rated voltage in sound proof room                                                    1M → 麦克风感应器

Background noise:14.9dBA                                                                                     MIC. Sensor

通风状态                         (对准风扇中心距离 50CM) ★

Free air                                                                         (Aim to center of the fan)

风扇 Fan

4-12、特性定义 Characteristics definition:

4-12-1、额定电流 & 额定转速 & 额定操作功率，须在额定电压下；马达连续转 5 分钟达到规格下限，10 分钟达到正常值

Rated current, rated speed, and rated input power shall reach bottom line of specification after 5              minutes continuous rotation at rated voltage and reach standard specification after 10 minutes continuous at rated voltage.

4-12-2、起动电压是指当突然通电后能够使风扇起动之最低电压

Starting voltage is the least voltage that enables to start the fan by sudden power on.

5 保护功能 Protection( ■表示选择项 Said options）:

5-1、马达保护 Motor protected:■阻抗保护 Impedance protected,□温控保护 Thermal protected.

5-2、风扇旋转锁定测试：将风扇通电锁死测试至少 12 小时，当锁定解除之后均仍然正常运转。

Fans spin lock test: Fan power will be tested at least 12 hours locked,when the lock is still      after     the lifting of the normal operation of

6、安全规格 Safety

UL

TUV

CE

7、原材料 Material

项次

Item

主要元件

Major components

材质或型式

等级

UL 号码

UL No.

备注

Remark

7-1

外框

Fan housing

铝框

Aluminum box

7-2

扇叶

Fan blade

PBT 85% + Fiber 15%

7 片叶

7-3

轴心

Stator core

不锈钢

Stainless steel (SUS420J2)

7-4

轴承

Bearing

滚珠轴承或含油轴承

Ball     bearing     or     sleeve bearing    (Cu+GLY)-2100

滚珠轴承

TWO BALL BEARING

7-5

线架

Line frame

PA6/66 加纤 5%-25%

防火 V0 本色

7-6

矽钢片

Silicon steel strip

H-60

7-7

漆包线

Enameled wires

去膜直径 0.09~0.096mm Material    &     Specification

0.09~0.096mm

MW-2 UEW

耐  热    Heat resistance155℃

7-8

电源线 Lead wires

7-9

贴纸 Label

多元脂

Polyester

8、出货检验程序 Product inspection procedure

本公司出货检验程序均依照下列步骤实施 Inspection procedures below are extremely followed

8-1、100% 生产线上电性，死角，扇叶拉拔

100% Electric, rotating, dead spot, fan blade fasten, and primary noise test on production line

8-2、100%以手敲击测试及静音室异音过滤

100% Strike test by hand and noise filter in quiet room

8-3、10 cm 落地试验依附 MIL-STD-105E 作抽样

10 cm drop test at random in accordance with MIL-STD-105E standard

8-4、出货抽样检验依 MIL-STD-105E 作允退判定

Random inspection in accordance with MIL-STD-105E standard

8-5、允退标准如下 Pass/Reject standard:

加严 Critical AQL:0.4                       正常 Major AQL:0.65                宽 松 Minor AQL:1.0

9、注意事项(Notes):

9-1、使用时请勿超出本规格所规定之极限，否则我们不保证此产品

We will not guarantee the products if the application of our products are exceeded the limitation which is specified on this specification.

9-2、倘若要变更此份文件的任何规格，请务必事先提出需求

In case of changes of the specification specified on this document.A written notice is requested in advance.

9-3、请勿触压着叶片以及电源线缠绕着风扇或用力拉扯电源线，如此轴心与电源线将会被损毁

Please do not touch the impeller with the pressure and never bring the fan with lead wire.The bearing and lead wire may be damaged.

9-4、本产品不保证因粉尘、水滴、小虫进入，而影响寿命与不良品产生

No guarantee on the products against the safety problem or failure caused by powder dust, drop of water or insect.

9-5、如有任何资料及文件与此份资料不同，将以此份资料为主要参考

If there is any data or related documentation different from this data sheet.This data sheet is the principle reference.

9-6、请勿在可燃性气体与任何有害环境中使用

Please do not use the fan in the environment of corrosive gas or liquid or any detrimental gas.

9-7、请于六个月内使用，否则风扇存放在很高温或很低温，温度很高或室温中风扇于六个月后会有漏电流产生Please do not store the fan in the environment of high/low temperature, high humidity or detrimental gas.

Please store within six months,every six months,shall be a leakage of electric current to the fan, even though thg  fan is stored in roo

9-8、当风扇于运转中，请勿企图将风扇锁死特别长的时间，如此，会因连续停止不转，产生高热而烧毁风扇While the fan is in operation, please do not lock the fan intentionally for a long periods of time, since the

continuous stoppage will result in overheat and thus burnt out the fan

9-9、组装风扇时，请特别注意，因共振或振动产生的噪音

During the installation of the fan, please pay substantial attention to possible notice caused by resonance vibration and shock.

9-10、当搬运或作业中，风扇如从 60cm 的高度落下，将会对叶片的平衡产生若干影响，特别是滚珠轴承避免掉落

It is very important to notify that avoid to drop from 60cm height when in any movement or operation,it will impact the balance of blade. Especially ball bearing structure is avoided to drop down.

9-11、锁外壳之螺丝扭力不得超 4Kgf

The torque of the screw which locked the frame should not exceed 4 Kgf